Skip to content
New Concept Auto Service Honest · Accurate · New Concept
Mon–Fri · 7:30am–5:30pm 5 Johnson County Shops
№ 01
Engine Repair

Engine Repair

Expert Engine Repair in Overland Park, South Overland Park, Merriam, Shawnee & Olathe, KS.

Book Service
ASE-Certified TechniciansFree Check-Engine-Light ScanHonest Photo-Documented Estimates5-Yr / 50k-Mile Warranty
OverviewFig. 02

The engine is the heart of your vehicle — and the sooner a noise, leak, or warning light is read correctly, the smaller the repair usually stays.

Engines are built to run for a very long time, but they depend on dozens of parts staying in balance — fuel, spark, air, oil, and cooling all arriving in the right amount at the right moment. When one of those falls out of step, the symptoms can range from a rough idle to a check-engine light to a knock you can hear from the driver's seat.

At New Concept, engine work begins with finding out what the vehicle is actually doing — scanning for codes, checking oil and coolant condition, and testing for the mechanical health underneath the symptom. We'd rather identify the true cause than throw parts at a problem, and we show you what we find before any repair is recommended.

Symptom Explorer

Signs your engine needs attention

Engine symptoms are worth taking seriously early, when the fix is usually smaller. Each of these points to a likely cause, but a scan and inspection are what confirm it.

A note on symptoms — These signs indicate a likely cause, not a diagnosis. The engine is a complex system, so a professional inspection is needed to know what's really happening.

A rough or uneven idle often points to a misfire — a cylinder that isn't firing cleanly. Worn spark plugs, a failing ignition coil, a vacuum leak, or a fuel-delivery issue can all cause it. A scan usually identifies which cylinder is affected, which narrows the search considerably.

A steady check-engine light means the computer has stored a fault worth reading; a flashing one usually signals an active misfire serious enough to risk the catalytic converter. Either way, the stored codes point us toward the system at fault. Our check-engine scan is free.

Oil leaks commonly come from valve-cover, oil-pan, or crankshaft seals and gaskets that have hardened with age and heat. A burning smell can mean oil is dripping onto a hot exhaust component. Because low oil is hard on an engine, leaks are worth tracing before they grow.

Engine noises can come from many places — low oil, worn valvetrain parts, or timing components among them. A deep knock that rises with RPM is treated more urgently than a light tick. Pinpointing the sound takes a listen and inspection rather than a guess.

When an engine feels sluggish, hesitates on acceleration, or starts drinking more fuel than usual, the cause can be ignition, fuel delivery, air intake, or a sensor reporting bad data. Live data from a scan helps show whether the engine is getting what it needs to run efficiently.

An engine that overheats is at real risk of serious internal damage, and the cause often lies in the cooling system rather than the engine itself. A thermostat, water pump, radiator, or leak can all be behind it. If the gauge climbs into the red, it's safest to stop and let it cool.

How It WorksComponent Explorer

The systems that keep an engine running

01

Ignition system

Spark plugs and ignition coils light the fuel-air mixture at precisely the right instant. As plugs wear or a coil weakens, you get misfires, rough running, and lost efficiency — which is why the ignition system is an early stop when a misfire shows up.

02

Fuel & air intake

The engine needs the right blend of fuel and clean air to make power. Injectors, filters, and intake components all play a part, and a restriction or leak here shows up as hesitation, rough idle, or weak acceleration.

03

Valvetrain & timing components

The timing belt or chain keeps the valves opening in sync with the pistons. If timing drifts or a worn component slips, the engine can run poorly or, in some designs, suffer real damage — so timing parts are serviced on schedule rather than run to failure.

04

Lubrication system

Oil and the oil pump reduce friction and carry away heat from moving parts. Low oil, a leak, or a neglected oil change leads to accelerated wear and engine noise, which is why oil level and condition are checked at nearly every visit.

05

Cooling system interface

The engine depends on the cooling system to hold a safe operating temperature. A failing thermostat, water pump, or coolant leak can let the engine overheat, so a cooling problem is often the real story behind an engine running hot.

06

Sensors & engine controls

Oxygen, mass-airflow, crankshaft, and other sensors feed data to the computer that manages fuel and timing. When a sensor reports bad information, the engine can run poorly even when the mechanical parts are fine — so sensor data is part of every diagnosis.

Why Diagnostics Matter

Reading the engine before repairing it

A check-engine light, a misfire, and a rough idle can all share the same root cause — or three different ones. Replacing parts in the hope of landing on the right one gets expensive fast and often leaves the real problem in place. The value of a proper engine diagnosis is that it separates the symptom from the cause.

We pull stored and live data, check oil and coolant condition, and test the mechanical and electrical health behind the symptom. When the picture is clear, we explain what's failing and why — in plain language, with the findings in front of you — so the repair you authorize is the one the engine actually needs.

  • 01Stored and live engine data read, not assumed
  • 02Misfires traced to the specific cylinder and cause
  • 03Oil, coolant & mechanical health checked together
  • 04Findings shown and explained before any repair
What's Included№ 06 — Scope of Work

Engine repairs we handle

From tune-up work to leaks, timing, and sensor faults, we cover the mechanical and electronic repairs that keep an engine running right — and we start by confirming the cause.

01

Check-engine-light diagnosis

Reading the stored and live codes to find the real cause behind the light, with a free scan to get started.

02

Misfire & rough-idle repair

Tracing a shaking or stumbling engine to the specific cylinder and the ignition, fuel, or mechanical cause behind it.

03

Spark plug replacement

Replacing worn plugs to restore smooth running, efficient combustion, and reliable starts.

Repair details
04

Timing belt replacement

Replacing the timing belt on schedule to keep the valves in sync and avoid the damage a failure can cause.

Repair details
05

Oil leak diagnosis & repair

Finding and sealing leaks from valve-cover, oil-pan, and crankshaft seals before low oil can harm the engine.

06

Engine sensor diagnosis

Testing and replacing sensors that feed the engine computer bad data and cause poor running or a warning light.

07

Overheating diagnosis

Finding why an engine runs hot, often in the cooling system, before heat can cause lasting internal damage.

08

Valve-cover & gasket service

Replacing hardened gaskets and seals that let oil escape onto hot engine components.

09

Drive belt & tensioner service

Replacing cracked or squealing belts and worn tensioners that drive the engine's accessories.

When To Come In№ 07

When to have your engine checked

Engine problems are almost always cheaper to address early. Here's what should prompt a visit.

Watch for
  • A check-engine light, especially a flashing one
  • Rough idle, misfires, or hesitation
  • Oil spots under the car or a burning smell
  • A new knock, tick, or the temperature gauge climbing
If you wait
  • A flashing check-engine light can damage the catalytic converter
  • Running low on oil accelerates internal wear fast
  • A slipped timing component can bend valves in some engines
  • Ignoring overheating risks serious, costly engine damage
Stay ahead
  • Keep up with oil changes on your manual's schedule
  • Have the check-engine light scanned promptly — it's free here
  • Replace the timing belt at the recommended interval
  • Address leaks and new noises before they grow
Safety first
  • Pull over safely if the temperature gauge reaches the red
  • A flashing check-engine light means service it soon
  • Don't keep driving on a loss of power you can't explain
  • We'll tell you honestly whether it's safe to keep driving
The Process

What to expect, start to finish

The same disciplined workflow on every job — so you always know what's happening and why.

  1. 01

    Initial inspection

    We start by listening to how the vehicle is behaving, then put it on the lift for a hands-on look at the system you came in for.

  2. 02

    Diagnostic testing

    Where a fault is electronic or intermittent, we scan control modules and test live data instead of guessing at parts.

  3. 03

    Findings & explanation

    You get a plain-language rundown of what we found — often with photos — so the problem is clear before any work is quoted.

  4. 04

    Repair recommendations

    We separate what needs attention now from what can safely wait, with an honest written estimate.

  5. 05

    Your authorization

    Nothing happens until you approve it. No surprise add-ons, no pressure.

  6. 06

    Professional repair

    ASE-certified technicians complete the work with quality parts, torqued and fitted to spec.

  7. 07

    Quality verification

    We re-test and road-check the repair, then hand the vehicle back backed by our nationwide warranty.

QuestionsFAQ

Frequently asked questions

Not always, but it should never be ignored. A steady light can be anything from a loose gas cap to a sensor or a developing problem, while a flashing light usually means an active misfire that can damage the catalytic converter. We scan it for free and read the codes so you know which situation you're in.
A misfire means one or more cylinders aren't firing cleanly, and the cause can be ignition (worn plugs or a failing coil), fuel delivery, a vacuum leak, or a mechanical issue inside the engine. A scan usually identifies the affected cylinder, which narrows it down quickly. From there we test to confirm the specific cause before replacing anything.
Leaks typically come from gaskets and seals that harden with age and heat, while oil consumption can relate to internal wear. Either way, running low on oil is hard on an engine, so it's worth tracing. We locate the source and show you where it's coming from before recommending a repair.
Timing belts are replaced on a mileage or time interval listed in your owner's manual, not when they fail — because in many engines a snapped belt can bend valves and cause major damage. If you're near the interval or unsure of your belt's history, it's worth checking. We can tell you whether your vehicle uses a belt or a chain and what's recommended.
Often the real cause is in the cooling system — a thermostat, water pump, radiator, or coolant leak — rather than the engine itself, though sustained overheating can damage the engine. If your gauge climbs into the red, it's safest to stop and let it cool to avoid lasting harm. We diagnose the cooling side and the engine side together to find the source.
Find A LocationFive Johnson County shops

Service near you

Book at the New Concept shop that's most convenient — same ASE-certified standards and nationwide warranty at every location.

01

Overland Park

9573 W 87th St, Overland Park, KS 66212
02

Merriam

6032 Merriam Dr, Merriam, KS 66203
03

Shawnee

4119 Bonner Industrial Dr, Shawnee, KS 66226
04

Olathe

128 N Mahaffie St, Olathe, KS 66061
05

South Overland Park

7601 W 119th St, Overland Park, KS 66213
Book an Appointment

Ready when you are.

Book online in under a minute, or call and talk to a real person. Honest estimates, no pressure — your dealership alternative in Johnson County.